I checked with Kat's and the correct location to install the Kat's Heaters Custom Fit Engine Block Heater part # KH11811 on a 2014 Chevrolet Impala Limited with 3.6L V6 Engine is on the rear left side of the engine as you can see in the attached photo labeled "RL". view full answer...
Only solution we can recommend for transporting a motorcycle of any kind with your 2014 Chevy Impala Limited is a small trailer. Even if you could fabricate a hitch for the vehicle with a 2 inch opening it wouldn't be strong enough and would potentially damage the vehicle/hitch as well as endanger other motorists.
For a hitch the Draw Tite part # 36407 would be a great option confirmed to fit. For trailer wiring you'd want the # C59496. For a ball mount then you'd want part # 36061 and... view full answer...
I'm glad to hear your trailer hitch receiver installation went well. For your 2015 Chevy Impala Limited, I recommend the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector # C59236 which has a max amperage of 5 amps on stop/turn lights and 7.5 amps on tail lights. This is a confirmed fit for your vehicle and will protect your factory wiring.
The Hopkins # HM48925 will only put out a max amperage of 2.1 per circuit so that won't help. There are many that could work,... view full answer...
For your 2014 Chevy Impala Limited the Draw Tite hitch part # 36407 that you referenced has been a confirmed fit and would work well.
For trailer wiring you then would want the part # C59236 which has been confirmed as a fit. The ball mount you would want is the part # 36061. For hitch balls you would want the # 19258 for a 2 inch ball and part # 19257 for a 1-7/8 inch ball. view full answer...
The problem is that your 2014 Chevy Impala Limited turn signal circuits do not have the amperage rating to handle the additional draw of your trailer tailights.
That's why you have to use a harness like the part # C59496 as it draws it's amperage from the vehicle battery. view full answer...
I do have a trailer hitch solution for you, Unfortunately, it will be an 1-1/4" trailer hitch. The Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4", part # C12252, is my recommended trailer hitch. It has a maximum tongue weight of 350 lbs and a maximum gross trailer weight of 3,500 lbs, which is more than our other options.
I prefer the Thule EasyFold XT Bike Rack for 2 Electric Bikes - 1-1/4" and 2" Hitches - Frame Mount, part # TH903202, when compared to the Saris SuperClamp... view full answer...
I did some research and found that the owner's manual for your 2015 Chevrolet Impala Limited states that the vehicle cannot be flat-towed.
If you need to tow your Impala I recommend using a tow dolly like part # RM-2050-1. This dolly comes with electric brakes and adjustable axle and ramps allow the dolly to fit almost any vehicle.
You will need a brake controller in your towing vehicle for this system. I recommend the Tekonsha Prodigy P3 Brake Controller, part # 90195. This is one of... view full answer...
When we installed the Draw Tite hitch part # 36407 we found that from the center of our hitch pin hole to the outermost point of the bumper is 6-1/2 inches.
If your bike rack has 11 inches from it's pin hole to the back of the upright mast this would easily clear. view full answer...
We have two trailer hitch receivers to fit your 2016 Chevrolet Impala Limited and they're both 1-1/4 inch Class II receivers. The Draw-Tite # 36407 and the Curt # C12252. They both have a maximum gross trailer weight of 3,000 pounds and a maximum tongue weight of 300 pounds. The Curt does require the use of a stabilization strap, part # 18050, in order to be in compliance with their warranty whenever carrying non-trailer loads. For this reason I suggest the Draw-Tite.
If you're going... view full answer...
There are a pair of trailer hitches which are confirmed fits for your 2014 Chevrolet Impala Limited, and each are Class II rated, the Draw-Tite, # 36407, or the Curt, # C12252. The receivers on these hitches are each 1-1/4 inches, and the gross trailer weight is 3,500 for each, while their tongue weight is 300 lbs; neither is rated for weight distribution.
If you are interested in towing with your Impala, I can recommend a ball mount for your hitch, the Curt # C45519, and the accompanying... view full answer...
We do have hitch mounted platform bike carriers that will be able to work with your Day6 Recumbent bike but the three bike carriers you mentioned will work with your bike.
I recommend the Holly7wood Racks Sport Rider 2, part # HR1000Z-R. This bike carrier has a weight capacity of 45-lbs per bike and can handle a wheelbase up to 74 inches. The distance form the hitch pin hole to the closest wheel hoop on the bike carrier is 8-1/2 inches.
If your Day6 bike is an electric bike I recommend... view full answer...
Go To Results